Biopol Paints Silicone Silver, heat resistant up to 500 °C, 80 g

The heat-resistant paint Biopol Paints Silicone Silver serves for effective protection of structures and objects made of steel and cast iron, which are subject to thermal and cyclic stress (heat exchangers, flue pipes, automotive exhausts, or steam pipes). The baked coating reliably resists diesel, gasoline, organic solvents, and diluted acid and alkali solutions. Silicone Silver was developed for the effective protection of steel and cast iron products and structures exposed to cyclic thermal load. The paint composition is based on top-quality silicone resin combined with a special aluminum mix that does not degrade even at temperatures around 500 °C. It withstands temperatures up to 500 °C for a long time. The product is very suitable for protecting motor parts, heat exchangers, flue pipes, exhausts from rusting steel, steel piping systems for hot and sharp steam, or venting systems of dryers. If you do not bake the coating, it has comparable resistance to weather influences; however, the film is softer and does not provide protection against the effects of organic solvents. The paint is applied in at least two layers, depending on the aggressiveness of the external environment. For normal weather conditions, the minimum layer of the cured film is 13 μm (corresponding to 3-4 coatings).

Drying:
within 45 minutes depending on environmental conditions, after 2 hours without imprint

Coverage:
5 - 7 m²/kg depending on the complexity and porosity of the surface being painted

Application:
with a brush, roller, spraying, dipping

Dilution and cleaning:
S6005, Xylene

Application:
The paint is applied with a brush, roller, spraying, or dipping. It is often preferable to paint the first layer. Between individual layers, allow time intervals of at least 4 hours under normal conditions. It is optimal to let each layer dry and bake at a temperature of 200 °C for 30 minutes. The coating system does not need to be baked, but it is softer and does not withstand the effects of organic solvents. When subsequently baking the entire coating system, ensure a gradual temperature rise!!! The most appropriate preparation of the steel and cast iron substrate is by sandblasting. Minimum requirements: removal of rust and old degraded coatings along with degreasing. The actual coating system usually consists of 3x SILICONE SILVER. For substrate preparation and application of the coating system, we recommend following the principles of the technical standards ČSN EN ISO 1 1-8 and accompanying regulations ČSN ISO 8501 850226.)

Product safety warnings (H-statements)

• H226: Flammable liquid and vapor.
• H304: May be fatal if swallowed and enters airways.
• H312+H332: Harmful to health in contact with skin or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H335: May cause respiratory irritation.
• H373: May cause damage to organs with prolonged or repeated exposure.

Safety handling instructions (P-statements)

• P102: Keep out of reach of children.
• P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
• P233: Keep container tightly closed.
• P260: Do not breathe dust/fume/gas/mist/vapor/aerosol.
• P271: Use only outdoors or in a well-ventilated area.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P301+P310: IF SWALLOWED: Immediately call a POISON CENTER/doctor.
• P303+P361+P353: IF ON SKIN (or hair): Remove/Take off immediately all contaminated clothing. Rinse skin with water/shower.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P331: DO NOT induce vomiting.
• P370+P378: In case of fire: Use extinguishing media according to the safety data sheet fire extinguishers/sand/carbon dioxide.