Biopol Paints Silicone Silver Paint, heat-resistant up to 500 °C, 350 g

Biopol Paints Silicone Silver Paint, this heat-resistant paint can be used for effective protection of steel and cast iron objects and structures that are exposed to cyclic and thermal stress (heat exchangers, flues, car exhausts, steam pipelines). The fired coating is resistant to organic solvents, diesel, gasoline, and diluted solutions of acids and bases. Silicone Silver Paint has been developed for effective protection of steel and cast iron objects and structures exposed to cyclic thermal stress. The paint is formulated based on premium silicone resin and a special aluminum composition that does not degrade even at temperatures around 500 °C. It permanently withstands temperatures up to 500 °C. The silver paint can be advantageously used to protect engine components, heat exchangers, flues, exhausts made of rusting steel, and steel pipes for both sharp and hot steam, as well as exhausts from dryers. The unburned paint has equivalent protective properties against weathering. However, it is softer and does not protect the substrate against organic solvents. The paint should be applied in at least two coats depending on the aggressiveness of the environment. For normal weather conditions, the minimum thickness of the cured film is 13 μm (corresponding to 3-4 coats).

Drying:
up to 45 minutes depending on environmental conditions, after 2 hours without imprint

Coverage:
5 - 7 m²/kg depending on the texture and porosity of the surface being painted

Application:
with a brush, roller, spraying, dipping

Dilution and cleaning:
S6005, Xylene

Application:
The paint is applied with a brush, roller, spraying, or dipping. It is usually better to apply the first coat with a brush. Between individual layers, allow a minimum of 4 hours between coats under normal conditions. It is optimal to let each layer dry and cure at a temperature of 200 °C for 30 minutes. The coating system does not need to be fired, but it is softer and does not withstand the action of organic solvents. When subsequently firing the entire coating system, take care for a gradual temperature rise!!! The most suitable preparation of both steel and cast iron substrates is blasting. Minimum requirements: removing the substrate from rust and old degraded coatings and degreasing. The actual coating system usually consists of 3x SILICONE SILVER PAINT. For substrate preparation and application of the coating system, we recommend following the principles of technical standards ČSN EN ISO 11-8 and accompanying regulations ČSN ISO 8501 850226.)

Product safety warnings (H-phrases)

• H226: Flammable liquid and vapors.
• H304: May be fatal if swallowed and enters airways.
• H312+H332: Harmful to health in contact with skin or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H335: May cause respiratory irritation.
• H373: May cause damage to organs with prolonged or repeated exposure.

Safe handling instructions (P-phrases)

• P102: Keep out of reach of children.
• P210: Keep away from heat, hot surfaces, sparks, open flames, and other ignition sources. No smoking.
• P233: Keep container tightly closed.
• P260: Do not breathe dust/fume/gas/mist/vapors/aerosols.
• P271: Use only outdoors or in a well-ventilated area.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P301+P310: IF SWALLOWED: Immediately call a POISON CENTER/doctor
• P303+P361+P353: IF ON SKIN (or hair): Remove all contaminated clothing immediately. Rinse skin with water/shower.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P331: DO NOT induce vomiting.
• P370+P378: In case of fire: Use extinguishing media according to the safety data sheet/extinguisher/sand/carbon dioxide to extinguish.