HB-Lak Sadurit Z1 anti-slip paint for concrete, gray, 4 kg + hardener Telalit 1 kg

Sadurit Z1 is a two-component anti-slip epoxy paint for concrete floors. Very high quality anti-slip, wheeled is resistant to oils and chemicals, used for finishing coats on concrete substrates. SADURIT Z1 (component A of the system) and TELALIT 160 (component B of the system) is a two-component colored solvent-based coating system with increased resistance to chemical and petroleum products.

We recommend using the system for floor renovations:

• Department stores and warehouses.
• Large-capacity garages, car workshops.
• Exhibition pavilions and demonstration shopping centers.
• Manufacturing and storage halls, food processing facilities.

Coverage:
5 m²/kg at 100 microns wet film. Consumption 0.2 kg/m².

Mixing ratio:
Component Z1: 100 wt. parts, component Telalit 160: 25 wt. parts.

Usage:
Sadurit Z1 is used as a coating for dust-free surface treatment of concrete, or other cohesive materials such as chipboard, etc. Its application can be found in garages, warehouses, machine rooms, assembly workshops, and production halls. It exhibits high wear resistance, good adhesion to the substrate, washability, and partial chemical resistance. The gray shade of Sadurit Z1 cured with Telalit T 160 is suitable for painting concrete surfaces in food processing facilities.

Processing technology procedure:
The substrate must be insulated or have a basement; otherwise, there is a risk of rising moisture from below, which usually leads to peeling of the coating. The concrete must be at least 28 days cured. The surface must not be troweled or covered with excessive cement laitance. The substrate must be free of all mechanical impurities, grease, or residues of old coatings. Sadurit Z1 should be thoroughly mixed before hardening to ensure all thicker filler components are well blended. Both components are then mixed in the specified ratio by slow, thorough stirring. The working time of the hardened mixture at 20 °C is 4 hours. The application is best done with asphalt brooms or velour rollers. The thickness of the undiluted wet coating should be 100 to 200 microns. Applying thicker layers can impair the evaporation of the contained solvents and prolong the time for complete curing. In worse cases, surface cracking can occur and areas of depression may develop marbling due to the stratification of pigments of varying densities. More heavily loaded areas or porous substrates should be penetrated with a coating diluted by 10 to 15% S6300. The next coat is applied after 24 hours.

Product safety warnings (H-phrases)

• H226: Flammable liquid and vapors.
• H304: May be fatal if swallowed and enters airways.
• H312: Harmful in contact with skin.
• H314: Causes severe skin burns and eye damage.
• H315: Causes skin irritation.
• H317: May cause an allergic skin reaction.
• H318: Causes serious eye damage.
• H319: Causes serious eye irritation.
• H332: Harmful if inhaled.
• H335: May cause respiratory irritation.
• H336: May cause drowsiness or dizziness.
• H373: May cause damage to organs with prolonged or repeated exposure.

Safe handling instructions (P-phrases)

• P101: If medical advice is needed, have product container or label at hand.
• P102: Keep out of reach of children.
• P103: Read label before use.
• P210: Keep away from heat, hot surfaces, sparks, open flames, and other ignition sources. No smoking.
• P233: Keep container tightly closed.
• P240: Ground container and receiving equipment.
• P242: Use only non-sparking tools.
• P243: Take preventive measures against static discharge.
• P251: Do not pierce or burn, even after use.
• P261: Avoid breathing dust/fume/gas/mist/vapors/aerosols.
• P264: Wash all affected body parts thoroughly after handling, such as hands
• P271: Use only outdoors or in a well-ventilated area.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P301+P310: IF SWALLOWED: Immediately call a TOXICOLOGICAL INFORMATIONCENTER/doctor/ tel. 224 919 293 or 224 915 402 (24 hours a day)
• P303+P361+P353: IF ON SKIN (or hair): Remove all contaminated clothing immediately. Rinse skin with water/shower.
• P304+P340: IF INHALED: Move person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contactlenses, if present and easy to do. Continue rinsing.
• P310: Immediately call a TOXICOLOGICAL INFORMATION CENTER/doctor/ tel. 224919 293 or 224 915 402 (24 hours a day)
• P312: If you feel unwell, call a TOXICOLOGICAL INFORMATIONCENTER/doctor/ tel. 224 919 293 or 224 915 402 (24 hours a day)
• P321: Specialized treatment (see … on the label).
• P331: DO NOT induce vomiting.
• P332+P313: If skin irritation occurs: Get medical advice/attention.
• P362: Take off contaminated clothing.
• P370+P378: In case of fire: Use extinguishing agent/sand/carbon dioxide as per safety data sheet to extinguish.
• P403+P233: Store in a well-ventilated place. Keep container tightly closed.
• P403+P235: Store in a well-ventilated place. Keep cool.
• P405: Store locked up.
• P501: Dispose of contents/container in accordance with product instructions.