Detecha Izoban concrete paint, RAL 9003 white, 2 kg

Synthetic coating for concrete. 100% waterproof, resistant to oils, salt solutions, weak acids and alkalis, temporarily to diesel fuel. Mechanically resistant. Withstands permanent thermal loads up to +50 °C. Easily repairable by simple recoating. A product with an excellent quality-to-price ratio.

Usage:
Outdoor and indoor coatings for concrete. Concrete floors (garages, non-residential areas, basements, workshops, balconies, etc.). Concrete swimming pools, water tanks (certificate SZÚ Prague), masonry, plasters. Steel tanks with a basic anti-corrosive primer (e.g. Fest Primer, Superkov, etc.)

Warning:
Walkable after 8 hours. Filling the pool after 7 days. Final curing takes 14 days to 3 weeks.

Dilution:
If necessary, the paint can be thinned with solvent S 6005.

Yield:
The yield of the coating depends on the quality of the coated surface and ranges from 6 - 8 m² per 1 kg in one layer at an average dry film thickness of 50 μm.

Substrate preparation:
The concrete must be absorbent, optionally roughened, not cast, well-cured, dry (maximum relative humidity of the substrate 15%), insulated against moisture from below. It must be cohesive (cohesion of the concrete in tension min. 1.5 MPa), free of all dirt and poorly adhering particles. In case of doubt about the suitability for the given substrate (e.g. leveling compound, old coating) it is recommended to perform a test coating on a smaller area.

Application method:
Before use, the material must be thoroughly mixed and diluted if necessary. It is recommended to perform penetration with a diluted coating in a ratio of 1 part Izoban to 1 part solvent S 6005 before coating untreated concrete surfaces. For larger areas, it is advisable to use material from one production batch, or to mix different batches to ensure a uniform color shade. It is applied with a brush or roller in at least two layers depending on the absorbency of the substrate, always after the previous layer has dried. The thickness of the entire coating system after drying must be approximately 100 µm. A thicker layer of paint significantly prolongs drying and curing time, so it is necessary to proceed with thin layers. For coatings of steel tanks and barrels, it is recommended to pre-coat the surface with a basic anti-corrosive primer (Fest primer and Superkov) and to perform the subsequent Izoban coating only after the primer has fully cured for at least 48 hours. Work in a well-ventilated environment at a temperature between +10 and +25°C. Do not work in direct sunlight!

Warning:
The paint is not intended for coatings that come into direct contact with food, feed, and drinking water, and for coatings of children's furniture and toys. It cannot be applied to insufficiently dried substrates, e.g. in damp, poorly ventilated areas. The coating is not resistant to gasoline and organic solvents.

Product safety warnings (H-statements)

• EUH066: Repeated exposure may cause dryness or cracking of the skin.
• H226: Flammable liquid and vapour.
• H312: Harmful to health in contact with skin.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H332: Harmful to health if inhaled.
• H335: May cause respiratory irritation.
• H362: May harm breastfed babies through breast milk.
• H373: May cause organ damage with prolonged or repeated exposure.
• H411: Toxic to aquatic organisms, with long-lasting effects.

Safety handling instructions (P-statements)

• P102: Keep out of reach of children.
• P201: Obtain special instructions before use.
• P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
• P263: Avoid contact during pregnancy/breastfeeding.
• P271: Use only outdoors or in a well-ventilated area.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P302+P352: IF ON SKIN: Wash with plenty of water and soap
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If feeling unwell, call the TOXICOLOGY INFORMATION CENTER/doctor/tel. 224 919 293 or 224 915 402 (24 hours a day)
• P391: Collect spillage.
• P501: Dispose of contents/container according to the instructions on the product.