Detecha Izoban concrete paint, gray, 2 kg

Synthetic coating for concrete. 100% waterproof, resistant to oils, salt solutions, weak acids and bases, short-term to motor diesel. Mechanically durable. Tolerates permanent thermal loads up to +50 °C. Easily repairable with simple re-coating. A product with an excellent quality-to-price ratio.

Application:
Outdoor and indoor coatings for concrete. Concrete floors (garages, non-residential areas, basements, workshops, balconies, etc.). Concrete pools, water reservoirs (certified by SZÚ Prague), masonry, plasters. Steel tanks with a basic anti-corrosion primer (e.g. Fest Primer, Superkov, etc.)

Notice:
Walkable in 8 hours. Pool filling after 7 days. Final curing takes 14 days to 3 weeks.

Dilution:
If necessary, the coating can be thinned with thinner S 6005.

Yield:
The yield of the coating material depends on the quality of the coated surface and ranges from 6 - 8 m² per 1 kg in one layer at an average dry film thickness of 50 μm.

Substrate preparation:
Concrete must be absorbent, optionally roughened, not caked, well-hardened, dry (maximum relative humidity of the substrate 15%), insulated against rising moisture. Must be cohesive (cohesion of concrete in tension min. 1.5 MPa), free of all contaminants and poorly adhering particles. In case of doubt about the suitability of use on the given substrate (e.g. leveling compound, old coating), it is recommended to perform a test coating on a smaller area.

Application method:
Before use, the material must be thoroughly mixed and diluted if necessary. Before coating untreated concrete surfaces, it is recommended to apply a primer with a diluted coating in a ratio of 1 part Izoban to 1 part thinner S 6005. For larger areas, it is recommended to use material from one production batch, or mix different batches to ensure a uniform color shade. It is applied with a brush or roller in at least two layers depending on the absorbency of the substrate, always after the previous layer has dried. The total thickness of the entire coating system must be approximately 100 µm after drying. A thicker layer of paint significantly prolongs the drying and curing time, so it is necessary to proceed with thin layers. In the case of coatings on steel tanks and barrels, it is recommended to pre-treat the surface with a basic anti-corrosion primer (Fest primer and Superkov) and apply the subsequent Izoban coating only after the primer has fully cured, at least after 48 hours. Work in a well-ventilated environment at temperatures between +10 and +25°C. Do not work in direct sunlight!

Notice:
The paint is not intended for coatings that come into direct contact with food, feed, and drinking water, and for coatings of children's furniture and toys. It cannot be applied to insufficiently dried substrates, e.g. in damp poorly ventilated areas. The coating does not withstand the action of gasoline and organic solvents.

Product safety warnings (H-statements)

• EUH066: Repeated exposure may cause skin dryness or cracking.
• H226: Flammable liquid and vapors.
• H312: Harmful to health in contact with skin.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H332: Harmful to health if inhaled.
• H335: May cause respiratory irritation.
• H362: May harm breastfeeding infants through breast milk.
• H373: May cause organ damage with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safe handling instructions (P-statements)

• P102: Keep out of reach of children.
• P201: Obtain special instructions before use.
• P210: Protect from heat, hot surfaces, sparks, open flame and other ignition sources. No smoking.
• P263: Avoid contact during pregnancy/breastfeeding.
• P271: Use only outdoors or in a well-ventilated area.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P302+P352: IF ON SKIN: Wash with plenty of soap and water
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call the POISON CENTER/doctor/tel. 224 919 293 or 224 915 402 (24 hours a day)
• P391: Collect spillage.
• P501: Dispose of contents/container in accordance with product instructions.