Formex S2003 base for galvanized basic paint for metal, 0600 gray-green, 0.6 l

Basic synthetic anti-corrosive paint designed for coatings of light colored metals and iron.

CHARACTERISTICS AND USAGE:

The paint is intended for primer coatings of light colored metals and iron, e.g. metal structures, frames, fittings, sills, gutters, car bodies, sheet roofs, steel castings, cast iron and sheet radiators for hot water heating. It is also suitable for steel coatings under nitrocellulose and synthetic paints drying in air. It is characterized by quick drying and excellent adhesion to various substrates.

Key properties:

• anti-corrosive coating
• excellent adhesion to steel and light metals
• also suitable under nitrification and polyurethane coatings

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free from grease, rust, and dust, and mechanically cleaned. Coating on galvanized sheet is possible after at least 12 months of exposure to weathering effects. First of all, the surface must be degreased using a suitable cleaning agent (e.g., BALTECH P6402 technical gasoline, BALTECH P6401 acetone or, where possible, warm pressurized water with detergent content). To remove residues of various salts, it is necessary to rinse the surface subsequently with clean water. Coarse and well-adhering contaminants must be removed manually or mechanically (by grinding, scraping). Any rust can also be removed manually or mechanically (with metal brushes, grinding discs) or using rust removers. If chemical rust removers are used, subsequent rinsing with clean water is necessary.
Previously painted surfaces must be cleaned, degreased, and stripped of old non-adhering coatings.

DILUTION: thinner BALTECH S6005 (brush, roller), thinner BALTECH C6000 (spraying)

Theoretical yield: 10 - 12 m²/l.

WORKING PROCEDURE:

Before use, thoroughly mix the contents and dilute if necessary. The paint is applied with a brush, roller, or spraying onto the pre-prepared surface.
1. One coat with FORMEX FOR GALVANIZED S2003. It dries at a temperature around 20 °C. Drying can be accelerated by forced drying at up to 80 °C. The air-dried coat can be over-coated within 1 hour with synthetic or nitrocellulose paint, the optimal thickness of one layer is 35-40 µm.
2. 2 to 3 coats with INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, or INDUSTROL PROFI U2129.

Product safety warnings (H-statements)

• EUH208: Contains (see hazardous substances). May cause an allergic reaction.
• EUH211: Warning! Spraying may produce dangerous respirable droplets. Do not breathe aerosols or mist.
• H226: Flammable liquid and vapors.
• H312+H332: Harmful to health upon skin contact or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H335: May cause respiratory irritation.
• H373: May cause damage to organs with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safety handling instructions (P-statements)

• P102: Keep out of reach of children.
• P210: Protect from heat, hot surfaces, sparks, open flame, and other ignition sources. No smoking.
• P261: Avoid breathing dust/fume/gas/mist/vapors/aerosols.
• P273: Prevent release to the environment.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P304+P340: IF INHALED: Move person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: Call a POISON CENTER or doctor if you feel unwell.
• P501: Dispose of contents/container in accordance with product instructions.