Formex S2003 primer for galvanized basic paint for metal, 0840 red-brown, 600 ml

Basic synthetic anticorrosive paint intended for coatings of light colored metals and iron.

CHARACTERISTICS AND USE:

The paint is intended for primer coatings of light colored metals and iron, e.g. metal structures, frames, fittings, sills, gutters, car bodies, metal roofs, steel castings, cast iron and sheet radiators for hot water heating. It is also suitable for coatings of steel under nitrocellulose and synthetic paints drying in air. It features rapid drying and excellent adhesion to various substrates.

Key properties:

• anticorrosive coating
• excellent adhesion to steel and light metals
• also suitable under nitro-combination and polyurethane coatings

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free from grease, rust, and dust, and mechanically cleaned. Coating on galvanized sheet metal is possible only after 12 months of exposure to weather conditions. First, the surface must be degreased using an appropriate cleaning agent (e.g. BALTECH P6402 technical benzene, BALTECH P6401 acetone, or when possible, warm pressurized water with detergent). To remove any residues of various salts, the surface must then be rinsed with clean water. Coarse and well-adhered contaminants must be removed manually or mechanically (sanding, scraping). Any rust can also be removed manually or mechanically (metal brushes, sanding discs) or using rust removers. If chemical rust removers are used, a subsequent rinse with clean water is required.
Previously coated surfaces must be cleaned, degreased, and stripped of old non-adhering coatings.

DILUTION: diluent BALTECH S6005 (brush, roller), diluent BALTECH C6000 (spraying)

Theoretical coverage: 10 - 12 m²/l.

WORKING PROCEDURE:

Before use, mix the contents thoroughly and dilute if necessary. The paint is applied with a brush, roller, or spraying on a previously prepared surface. 
1. One coat with FORMEX NA POZINK S2003 paint. It dries at a temperature of around 20 °C. Drying can be accelerated by drying at up to 80 °C. The air-dried coat can be overcoated after just 1 hour with synthetic or nitrocellulose enamel, with an optimal thickness of a single layer being 35-40 µm.
2. 2 to 3 coats with INDUSTROL UNIVERZÁL S2013, INDUSTROL PLUS S2071, or INDUSTROL PROFI U2129.

Product safety warnings (H-statements)

• EUH208: Contains (see hazardous substances). May produce an allergic reaction.
• EUH211: Warning! Spraying may produce hazardous respirable droplets. Do not inhale aerosols or mist.
• H226: Flammable liquid and vapors.
• H312+H332: Harmful to health in contact with skin or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H335: May cause respiratory irritation.
• H373: May cause damage to organs with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long lasting effects.

Instructions for safe handling (P-statements)

• P102: Keep out of reach of children.
• P210: Protect from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
• P261: Avoid breathing dust/fume/gas/mist/vapors/aerosols.
• P273: Avoid release to the environment.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P304+P340: IF INHALED: Move person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call a POISON CENTER/doctor.
• P501: Dispose of contents/container in accordance with the instructions on the product.