Detecha Estedien EK 90 penetrating lacquer for concrete and absorbent substrates, 4 kg

Insulating impregnation and penetrating lacquer based on synthetic materials designed for concrete and absorbent surfaces. It features excellent resistance to water as well as solutions of weak alkalis and acids. It prevents seepage, providing the substrate with protection against contamination and against the corrosive effects of acidic juices.

Usage:
Outdoor and indoor coatings. Concrete, concrete floors, silage pits, gutters, wastewater pits, paving, autoclaved aerated concrete, brick masonry, artificial sandstone, etc. The product can also be used on surfaces that come into direct contact with food and dishes.

Substrate preparation and application method:
The substrate must be dry (relative humidity max. 15 %), cohesive, mature, free of all mechanical contaminants and old non-adhesive coatings before application. Apply the product with a brush or roller. Work in a well-ventilated environment at a temperature range of +5 °C to +25 °C. Do not work in direct bright sunlight! The product should penetrate as much as possible into the substrate. For this reason, apply the first layer as a penetrating one, with the product diluted according to the absorbency of the substrate. On less absorbent substrates, ESTEDIEN EK 90 can be diluted up to a ratio of 1:1. Extremely absorbent and porous substrates (e.g., autoclaved aerated concrete) do not require penetration and are coated with undiluted ESTEDIEN EK 90. To create an insulating layer, apply ESTEDIEN® EK 90 until the coating forms a thin continuous film. The coating dries and can be recoated depending on the surrounding temperature within 3 hours. It reaches its final properties after 48 hours of drying under normal conditions (20 °C). It may come into contact with food and feed only after 14 days of drying and after previous thorough rinsing with drinking water.

Dilution:
S 6005

Consumption:
The consumption of ESTEDIEN EK 90 coating is strongly influenced by the roughness and absorbency of the surface. On standard absorbent substrates, it ranges from 0.2 – 0.5 kg/m² (yield 5 – 2 m² from 1 kg) for one layer. The consumption is higher for extremely porous and absorbent surfaces (autoclaved aerated concrete).

• Product density: 0.90 – 0.96 g/cm³
• Content of organic solvents: 0.62 – 0.66 kg / 1 kg of product
• Content of non-volatile substances: 29.9 – 31.8 % by volume
• Limit value of VOC (sub-category A/h): 750 g/l
• Maximum VOC content: 640 g/l
  

Product safety warnings (H-statements)

• EUH066: Repeated exposure may cause dryness or cracking of the skin.
• H226: Flammable liquid and vapors.
• H312: Harmful to health on skin contact.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H332: Harmful to health if inhaled.
• H335: May cause respiratory irritation.
• H362: May harm breastfeeding infants through breast milk.
• H373: May cause organ damage with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safe handling instructions (P-statements)

• P102: Keep out of reach of children.
• P201: Obtain special instructions before use.
• P210: Keep away from heat, hot surfaces, sparks, open flames, and other ignition sources. No smoking.
• P263: Avoid contact during pregnancy/breastfeeding.
• P271: Use only outdoors or in a well-ventilated area.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P301+P330+P331: IF SWALLOWED: Rinse mouth. DO NOT induce vomiting.
• P302+P352: IF ON SKIN: Wash with plenty of water and soap
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call a POISON CENTER/doctor
• P391: Collect spillage.
• P501: Dispose of contents/container in accordance with product instructions.