Pragoprimer Standard S2000 base color for metal, 0110 gray, 2.5 l

Basic synthetic anti-corrosion paint

CHARACTERISTICS AND USE:

Pragoprimer Standard S2000 is a universal base color for metal and absorbent substrates for both interior and exterior environments, especially under synthetic and air-drying coatings, for coatings of, for example, sheet metal constructions, machines, metal and wooden furniture, etc. The paint has excellent anti-corrosion properties, very fast drying, and universal applicability.

Key properties:

• active anti-corrosion pigment
• fast drying
• excellent adhesion

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free of grease, rust, and dust, and mechanically cleaned. First of all, the surface must be degreased with a suitable cleaning agent (e.g. BALTECH P6402 technical gasoline, BALTECH P6401 acetone, or where possible warm pressurized water with detergent). To remove any residual salts, the surface must be rinsed with clean water. Coarse and well-adhering dirt must be removed manually or mechanically (by sanding, scraping). Any rust can also be removed manually or mechanically (with wire brushes, sanding discs) or using rust removers. When using chemical rust removers, a subsequent rinse with clean water is necessary.
Absorbent substrates must first be treated with a suitable primer that ensures uniform absorbency of the substrate. Previously painted surfaces must be cleaned, degreased, and freed from old non-adhering coatings.

DILUTION: thinner BALTECH S6006 (brush, roller), thinner BALTECH S6001 (spraying)

Theoretical coverage: 18 - 21 m²/l per one coat

WORKING PROCEDURE:

Before use, thoroughly mix the contents and thin as necessary. The paint is applied with a brush, roller, or spraying on the pre-prepared substrate.
Coating / spraying metal:
When spraying, problematic areas (corners, edges, welds, surface defects) are first treated with a so-called strip coating with a brush, and only after this coating has tacked, the entire area is sprayed (including already painted problem areas).
1. 1x PRAGOPRIMER STANDARD S2000, drying time 24 hours. The optimal thickness of one layer is 25 -30 µm. Drying on metal objects can be accelerated by forced drying at a temperature of 80 °C.
2. filling as needed, e.g., with polyester filler BKP Rapid TOS.
3. sanding of filled areas with sandpaper no. 180 - 220 wet.
4. 1x PRAGOPRIMER STANDARD S2000.
5. sanding with sandpaper no. 280.
6. 2 to 3x enamel INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129, or matte INDUSTROL UNIMAT S2075.

Coating absorbent substrate:
1. 1x treatment with lazure S1023 LAZUROL CLASSIC, or S1033 LAZUROL IMPREGNATING BASE, drying time 24 hours.
2. 1x PRAGOPRIMER STANDARD S2000, drying time 24 hours.
3. 2 to 3x enamel INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129, or matte INDUSTROL UNIMAT S2075.
If filling is necessary, proceed as in the previous point (coating metal).

You may need covering material, such as paper masking tape or covering film, as well as sanding papers. Don't forget brushes and rollers.

Product safety warnings (H-statements)

• EUH208: Contains (see hazardous substances). May cause allergic reactions.
• EUH211: Warning! Dangerous respirable droplets may be formed when spraying. Do not breathe aerosols or mist.
• H226: Flammable liquid and vapor.
• H312+H332: Harmful to health upon contact with skin or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H372: Causes damage to organs with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safety handling instructions (P-statements)

• P102: Keep out of reach of children.
• P210: Protect from heat, hot surfaces, sparks, open flame, and other ignition sources. No smoking.
• P261: Avoid breathing dust/fume/gas/mist/vapors/aerosols.
• P273: Prevent release to the environment.
• P280: Wear protective gloves/protective clothing/eye protection/face shield.
• P304+P340: IF INHALED: Move person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call a TOXICOLOGICAL INFORMATION CENTER/doctor.
• P501: Dispose of contents/container according to the instructions on the product.