Pragoprimer Standard S2000 basic paint for metal, 0840 red-brown, 600 ml

Basic synthetic anti-corrosive paint

CHARACTERISTICS AND USE:

Pragoprimer Standard S2000 is a universal basic paint for metal and absorbent substrates for both indoor and outdoor environments, especially under synthetic and air-drying coatings, for painting e.g. metal structures, machinery, metal and wooden furniture, etc. The paint has excellent anti-corrosive properties, very fast drying time, and universal applicability.

Key properties:

• active anti-corrosive pigment
• fast drying
• excellent adhesion

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free of grease, rust, and dust, and mechanically cleaned. First of all, the surface must be degreased using an appropriate cleaning agent (e.g. BALTECH P6402 technical gasoline, BALTECH P6401 acetone, or where possible warm pressurized water with detergent). To remove any residues of various salts, the surface must then be rinsed with clean water. Coarse and well-adhering dirt must be removed manually or mechanically (sanding, scraping). Any rust can also be removed manually or mechanically (with metal brushes, sanding discs) or using rust removers. If chemical rust removers are used, a subsequent rinsing with clean water is necessary.
Absorbent substrates must first be impregnated with an appropriate primer that ensures uniform absorption of the substrate. Previously painted surfaces must be cleaned, degreased, and stripped of old non-adhering coatings.

DILUTION: thinner BALTECH S6006 (brush, roller), thinner BALTECH S6001 (spraying)

Theoretical coverage: 18 - 21 m²/l for one coat

WORKING PROCEDURE:

Before use, the contents are thoroughly mixed and diluted if necessary. The paint is applied with a brush, roller, or by spraying onto the pre-prepared substrate. 
Coating / spraying of metal:
When applying by spraying, first address the problematic areas (corners, edges, welds, surface defects) with a so-called strip coating using a brush, and only after this coating has partially dried is the entire surface sprayed (including the already painted problematic areas).
1. 1x PRAGOPRIMER STANDARD S2000, drying time 24 hours. The optimal thickness of one layer is 25 - 30 µm. Drying on metal items can be accelerated by forcing at a temperature of 80 °C
2. filling as needed, e.g. with polyester filler BKP Rapid TOS
3. sanding filled areas with sandpaper No. 180 - 220 wet
4. 1x PRAGOPRIMER STANDARD S2000
5. sanding with sandpaper No. 280
6. 2 to 3x enamel INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129, or matte INDUSTROL UNIMAT S2075

Coating absorbent substrate:
1. 1x impregnation with glaze S1023 LAZUROL CLASSIC, or S1033 LAZUROL IMPREGNATING PRIMER, drying time 24 hours
2. 1x PRAGOPRIMER STANDARD S2000, drying time 24 hours
3. 2 to 3x enamel INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129, or matte INDUSTROL UNIMAT S2075
If filling is needed, proceed as in the previous step (metal coating).

You may find covering materials, such as paper masking tape or covering film, or sanding papers. Don’t forget brushes and rollers.

Product safety warning (H-statements)

• EUH208: Contains (see hazardous substances). May produce an allergic reaction.
• EUH211: Warning! Spraying may produce dangerous respirable droplets. Do not inhale aerosols or mist.
• H226: Flammable liquid and vapors.
• H312+H332: Harmful to health on contact with skin or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H372: Causes damage to organs with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Instructions for safe handling (P-statements)

• P102: Keep out of reach of children.
• P210: Protect from heat, hot surfaces, sparks, open flame and other ignition sources. No smoking.
• P261: Avoid breathing dust/smoke/gas/mist/vapors/aerosols.
• P273: Avoid release to the environment.
• P280: Wear protective gloves/protective clothing/protective eyewear/face shield.
• P304+P340: IF INHALED: Move person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call the POISON CENTER/doctor.
• P501: Dispose of contents/container according to product instructions.