Pragoprimer Standard S2000 basic paint for metal, 0110 gray, 350 ml

Basic synthetic anticorrosive paint

CHARACTERISTICS AND USE:

Pragoprimer Standard S2000 is a universal basic paint for metal and absorbent substrates for interior and exterior environments, especially under synthetic and air-drying coatings, for painting, e.g., metal structures, machines, metal and wooden furniture, etc. The paint has excellent anticorrosive properties, very quick drying, and universal applicability.

Key properties:

• active anticorrosive pigment
• quick drying
• excellent adhesion

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free of grease, rust, and dust, and mechanically cleaned. First of all, the surface must be degreased using a suitable cleaning agent (e.g., BALTECH P6402 technical gasoline, BALTECH P6401 acetone, or where possible, hot pressurized water containing detergent). To remove any residues of various salts, the surface must then be rinsed with clean water. Coarse and well-adhering dirt must be removed manually or mechanically (sanding, scraping). Any rust can also be removed manually or mechanically (metal brushes, grinding discs) or using rust removers. In the case of using chemical rust removers, subsequent rinsing with clean water is required.
Absorbent substrates must first be treated with a suitable primer that ensures uniform absorption of the substrate. Previously painted surfaces must be cleaned, degreased, and stripped of old non-adhering coatings.

DILUTION: diluent BALTECH S6006 (brush, roller), diluent BALTECH S6001 (spraying)

Theoretical coverage: 18 - 21 m²/l for one coat

WORKING PROCEDURE:

Before use, thoroughly mix the contents and dilute if necessary. The paint is applied with a brush, roller, or spray onto the pre-prepared substrate.
Coating / spraying of metal:
When spraying, problematic areas (corners, edges, welds, surface defects) are first treated with a brush using a so-called strip coating, and only after this coating has set is the entire area sprayed (including already painted problematic areas).
1. 1x PRAGOPRIMER STANDARD S2000, drying of the coating 24 hours. The optimal thickness of one layer is 25 -30 µm. Drying on metal objects can be accelerated by forced drying at a temperature of 80 °C
2. filling as needed with polyester filler BKP Rapid TOS
3. sanding of filled areas with sandpaper no. 180 - 220 wet
4. 1x PRAGOPRIMER STANDARD S2000
5. sanding with sandpaper no. 280
6. 2 to 3x enamel INDUSTROL UNIVERZÁL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129, or matte INDUSTROL UNIMAT S2075

Coating of absorbent substrates:
1. 1x treatment with S1023 LAZUROL CLASSIC stain or S1033 LAZUROL IMPREGNATION BASE, drying 24 hours
2. 1x PRAGOPRIMER STANDARD S2000, drying 24 hours
3. 2 to 3x enamel INDUSTROL UNIVERZÁL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129, or matte INDUSTROL UNIMAT S2075
If filling is needed, the procedure is as in the previous step (metal coating).

You may find covering material, such as paper masking tape or covering film, and possibly sanding papers. Don't forget brushes and rollers.

Product safety warnings (H phrases)

• EUH208: Contains (see hazardous substances). May cause an allergic reaction.
• EUH211: Caution! Spraying may create hazardous respiratory droplets. Do not inhale aerosols or mist.
• H226: Flammable liquid and vapors.
• H312+H332: Harmful to health upon contact with skin or inhalation.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H372: Causes damage to organs with prolonged or repeated exposure.
• H411: Toxic to aquatic organisms, with long-lasting effects.

Instructions for safe handling (P phrases)

• P102: Keep out of reach of children.
• P210: Protect from heat, hot surfaces, sparks, open flame, and other ignition sources. No smoking.
• P261: Avoid breathing dust/smoke/gas/mist/vapors/aerosols.
• P273: Prevent release into the environment.
• P280: Wear protective gloves/protective clothing/eye protection/face shield.
• P304+P340: IF INHALED: Move person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call a TOXICOLOGICAL INFORMATION CENTER/doctor
• P501: Dispose of contents/container in accordance with product instructions.