Pragoprimer Standard S2000 basic paint for metal, 0110 gray, 9 l

Basic synthetic anti-corrosive paint

CHARACTERISTICS AND USE:

Pragoprimer Standard S2000 is a universal basic paint for metal and absorbent substrates for both interior and exterior use, especially under synthetic and air-drying coatings, for painting, for example, metal structures, machines, metal and wooden furniture, etc. The paint has excellent anti-corrosive properties, very quick drying, and universal applicability.

Key properties:

• active anti-corrosive pigment
• quick drying
• excellent adhesion

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free of grease, rust, and dust, mechanically cleaned. First of all, the surface must be degreased using a suitable cleaning agent (e.g., BALTECH P6402 technical benzine, BALTECH P6401 acetone, or where possible, warm high-pressure water with detergent). To remove any remaining salts, the surface must be rinsed with clean water afterward. Coarse and well-adhering dirt must be removed manually or mechanically (sanding, scraping). Any rust can also be removed manually or mechanically (metal brushes, grinding discs) or using rust removers. In the case of using chemical rust removers, a subsequent rinse with clean water is necessary.
Absorbent substrates must first be impregnated with a suitable impregnator, which ensures uniform absorbency of the substrate. Previously painted surfaces must be cleaned, degreased, and stripped of old non-adherent coatings.

DILUTION: thinner BALTECH S6006 (brush, roller), thinner BALTECH S6001 (spraying)

Theoretical coverage: 18 - 21 m²/l for one layer

WORKING PROCEDURE:

Before use, thoroughly stir the contents and dilute as necessary. The paint is applied with a brush, roller, or spraying onto the pre-prepared substrate.
Coating / spraying metal:
When applying by spraying, first treat the problematic areas (corners, edges, seams, surface defects) with a so-called band coating using a brush, and only after the coating has set, proceed to spray the entire area (including already painted problematic areas).
1. 1x PRAGOPRIMER STANDARD S2000, drying of the coating 24 hours. The optimal thickness of one layer is 25 - 30 µm. Drying on metal objects can be accelerated by heating to 80 °C.
2. filling as needed, e.g., with BKP Rapid TOS polyester filler
3. sanding filled areas with sandpaper no. 180 - 220 wet
4. 1x PRAGOPRIMER STANDARD S2000
5. sanding with sandpaper no. 280
6. 2 to 3x INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matte INDUSTROL UNIMAT S2075

Coating absorbent substrate:
1. 1x impregnation with S1023 LAZUROL CLASSIC glaze, or S1033 LAZUROL IMPREGNATING BASE, drying 24 hours
2. 1x PRAGOPRIMER STANDARD S2000, drying 24 hours
3. 2 to 3x INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matte INDUSTROL UNIMAT S2075.
In case of the need for filling, proceed as in the previous point (coating metal).

You may find cover materials such as paper adhesive tape or covering foil, possibly sandpapers. Don't forget brushes and rollers.

Product safety warnings (H-statements)

• EUH208: Contains (see hazardous substances). May cause an allergic reaction.
• EUH211: Warning! When spraying, dangerous respirable droplets may be formed. Do not inhale aerosols or mist.
• H226: Flammable liquid and vapors.
• H312+H332: Harmful to health in contact with skin or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H372: Causes damage to organs with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Instructions for safe handling (P-statements)

• P102: Keep out of reach of children.
• P210: Keep away from heat, hot surfaces, sparks, open flame and other ignition sources. No smoking.
• P261: Avoid breathing dust/fume/gas/mist/vapors/aerosols.
• P273: Avoid release to the environment.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P304+P340: IF INHALED: Transfer the person to fresh air and keep them in a position comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call the TOXICOLOGICAL INFORMATION CENTER/doctor.
• P501: Dispose of contents/container in accordance with product instructions.