Pragoprimer Standard S2000 basic metal paint, 0840 red-brown, 4 l

Basic synthetic anti-corrosive paint

CHARACTERISTICS AND USE:

Pragoprimer Standard S2000 is a universal basic paint for metal and absorbent substrates for indoor and outdoor environments, particularly for use under synthetic and air-drying coatings, for painting, for example, sheet metal structures, machines, metal and wooden furniture, etc. The paint has excellent anti-corrosive properties, very quick drying, and universal applicability.

Key properties:

• active anti-corrosive pigment
• quick drying
• excellent adhesion

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free of grease, rust, and dust, mechanically cleaned. First of all, the surface must be degreased using a suitable cleaning agent (e.g., BALTECH P6402 technical gasoline, BALTECH P6401 acetone or where possible, warm high-pressure water with detergent). To remove any residual salts, the surface must then be rinsed with clean water. Coarse and well-adhering contaminants must be removed manually or mechanically (by sanding, scraping). Any rust can also be removed manually or mechanically (metal brushes, abrasive discs) or using rust removers. If chemical rust removers are used, a subsequent rinse with clean water is necessary.
Absorbent substrates must first be impregnated with a suitable primer that ensures uniform absorbency of the substrate. Previously painted surfaces must be cleaned, degreased, and free of old non-adhering coatings.

DILUTION: thinner BALTECH S6006 (brush, roller), thinner BALTECH S6001 (spraying)

Theoretical coverage: 18 - 21 m²/l for one coat

APPLICATION PROCEDURE:

Before use, thoroughly mix the contents and dilute as needed. The paint is applied with a brush, roller, or by spraying on a pre-prepared substrate.
Coating / spraying metal:
When applying by spraying, problematic areas (corners, edges, seams, surface defects) are first treated with a brush using a so-called band coating and only after the paint has set, the entire area (including already painted problematic spots) is sprayed.
1. 1x PRAGOPRIMER STANDARD S2000, drying time of the coat 24 hours. The optimal thickness of one layer is 25 - 30 µm. Drying on metal items can be accelerated by drying at a temperature of 80 °C
2. filling as needed, e.g., with polyester filler BKP Rapid TOS
3. sanding of filled areas with sandpaper No. 180 - 220 wet
4. 1x PRAGOPRIMER STANDARD S2000
5. sanding with sandpaper No. 280
6. 2 to 3x INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matte INDUSTROL UNIMAT S2075

Coating absorbent substrate:
1. 1x impregnation with S1023 LAZUROL CLASSIC, or S1033 LAZUROL IMPREGNATION BASIS, drying time 24 hours
2. 1x PRAGOPRIMER STANDARD S2000, drying time 24 hours
3. 2 to 3x INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matte INDUSTROL UNIMAT S2075
If filling is needed, follow the procedure as described in the previous point (painting metal).

You may find covering material, such as masking tape or covering foil, or possibly sandpapers. Don't forget about brushes and rollers.

Product safety warnings (H-statements)

• EUH208: Contains (see hazardous substances). May cause an allergic reaction.
• EUH211: Warning! Spraying may create dangerous respirable droplets. Do not inhale aerosols or mist.
• H226: Flammable liquid and vapors.
• H312+H332: Harmful to health on contact with skin or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H372: Causes damage to organs through prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safety handling instructions (P-statements)

• P102: Keep out of reach of children.
• P210: Protect from heat, hot surfaces, sparks, open flame and other ignition sources. No smoking.
• P261: Avoid breathing dust/fume/gas/mist/vapors/aerosols.
• P273: Avoid release to the environment.
• P280: Wear protective gloves/protective clothing/protective eyewear/face shield.
• P304+P340: IF INHALED: Move person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call a POISON CENTER/doctor.
• P501: Dispose of contents/container in accordance with product instructions.