Pragoprimer Standard S2000 primer paint for metal, 0100 white, 9 l

Basic synthetic anticorrosive paint

CHARACTERISTICS AND USE:

Pragoprimer Standard S2000 is a universal primer paint for metal and absorbent substrates for indoor and outdoor environments, especially under synthetic and air-drying coatings, for painting e.g. sheet metal structures, machines, metal and wooden furniture, etc. The paint has excellent anticorrosive properties, very fast drying, and universal applicability.

Key properties:

• active anticorrosive pigment
• fast drying
• excellent adhesion

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free of grease, rust, and dust, and mechanically cleaned. First of all, the surface must be degreased using an appropriate cleaning agent (e.g. BALTECH P6402 technical benzene, BALTECH P6401 acetone or where possible warm pressurized water with detergent). To remove any residues of various salts, the surface must be rinsed with clean water. Coarse and well-adhered dirt must be removed manually or mechanically (by sanding, scraping). Any rust can also be removed manually or mechanically (metal brushes, sanding discs) or using rust removers. When using chemical rust removers, a subsequent rinse with clean water is required.
Absorbent substrates must first be impregnated with a suitable impregnating agent that ensures uniform absorption of the substrate. Previously painted surfaces must be cleaned, degreased, and freed from old non-adhering coatings.

DILUTION: thinner BALTECH S6006 (brush, roller), thinner BALTECH S6001 (spraying)

Theoretical coverage: 18 - 21 m²/l for one layer

WORKING PROCEDURE:

Before use, stir the contents thoroughly and dilute as needed. The paint is applied with a brush, roller, or by spraying onto a pre-prepared substrate.
Coating/Spraying metal:
When applying by spraying, problematic areas (corners, edges, welds, surface defects) should first be treated with a so-called strip coating using a brush, and only after this coating has begun to dry should the entire area be sprayed (including already painted problematic areas).
1. 1x paint PRAGOPRIMER STANDARD S2000, drying time 24 hours. The optimal thickness of one layer is 25 -30 µm. Drying on metal items can be accelerated by forced drying at a temperature of 80 °C
2. filling as needed, e.g. with polyester filler BKP Rapid TOS
3. sanding the filled areas with sandpaper No. 180 - 220 wet
4. 1x PRAGOPRIMER STANDARD S2000
5. sanding with sandpaper No. 280
6. 2 to 3x enamel INDUSTROL UNIVERZÁL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matte INDUSTROL UNIMAT S2075

Coating absorbent substrate:
1. 1x impregnation with stain S1023 LAZUROL CLASSIC or S1033 LAZUROL IMPREGNATING BASE, drying time 24 hours
2. 1x paint PRAGOPRIMER STANDARD S2000, drying time 24 hours
3. 2 to 3x enamel INDUSTROL UNIVERZÁL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matte INDUSTROL UNIMAT S2075
If filling is needed, the procedure is the same as in the previous point (coating metal).

You may find masking material, such as paper masking tape or masking film, or sandpapers. Don't forget about brushes and rollers.

Product safety warnings (H-statements)

• EUH208: Contains (see hazardous substances). May produce an allergic reaction.
• EUH211: Warning! Spraying may create dangerous respirable droplets. Do not inhale aerosols or mist.
• H226: Flammable liquid and vapors.
• H312+H332: Harmful to health in contact with skin or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H372: Causes damage to organs through prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safety handling instructions (P-statements)

• P102: Keep out of reach of children.
• P210: Protect from heat, hot surfaces, sparks, open flame, and other ignition sources. No smoking.
• P261: Avoid breathing dust/fume/gas/mist/vapors/aerosols.
• P273: Avoid release to the environment.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P304+P340: IF INHALED: Transfer person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: Call a POISON CENTER or doctor if you feel unwell.
• P501: Dispose of contents/container according to the instructions on the product.