Pragoprimer for Industry S2000P Primer for Metal and Absorbent Substrates, 0110 Gray, 10 kg

Basic synthetic anti-corrosion paint for metal.

CHARACTERISTICS AND USE:

Universal primer with excellent anti-corrosion properties, very fast drying, and versatile applicability. The paint is intended for priming steel and iron for both indoor and outdoor environments, especially under air-drying synthetic coatings. The paint can also be used for coating non-metal objects, but absorbent substrates must be pre-treated with a suitable impregnation primer. Examples of use: sheet metal constructions, machines, metal furniture, frames.

Key Properties:

• excellent adhesion to steel surfaces
• excellent anti-corrosion properties,
• very fast drying
• suitable for industrial applications

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free of grease, rust, and dust, and mechanically cleaned. First, the surface must be degreased using a suitable cleaning agent (e.g. BALTECH P6402 technical gasoline, BALTECH P6401 acetone, or where possible, warm high-pressure water with detergent content). To remove any residual salts, the surface must then be rinsed with clean water. Coarse and well-adhered contaminants must be removed manually or mechanically (sanding, scraping). Any rust can also be removed either manually or mechanically (metal brushes, sanding discs) or using rust removers. In the case of using chemical rust removers, a subsequent rinse with clean water is necessary.
Absorbent substrates must first be treated with a suitable primer that ensures uniform absorbency of the substrate. Previously painted surfaces must be cleaned, degreased, and freed from old non-adhering coatings.

DILUTION: thinner BALTECH S6006 (brush, roller), thinner BALTECH S6001P (spraying)

Theoretical Coverage: 12 - 15 m²/kg for one coat

WORKING PROCEDURE:

Before use, thoroughly mix the contents and dilute as needed. Apply with a brush, roller, or spraying on the pre-prepared substrate.
Coating / spraying of metal:
When applying by spraying, first treat problem areas (corners, edges, welds, surface defects) with a brush using a so-called striping coat, and only after this coat has set, spray the entire surface (including previously painted problem areas).
1. 1x paint PRAGOPRIMER FOR INDUSTRY S2000P, drying time for the coating 24 hours. The optimal thickness of one layer is 25 -30 µm. Drying on metal objects can be accelerated by drying at a temperature of 80 °C.
2. filling as needed, for example with polyester filler BKP Rapid TOS.
3. sanding of filled areas with sandpaper No. 180 - 220 wet.
4. 1x PRAGOPRIMER FOR INDUSTRY S2000P.
5. sanding with sandpaper No. 280.
6. 2 to 3x enamel INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matte INDUSTROL UNIMAT S2075

You may find covering material, such as paper masking tape or covering foil, as well as sanding papers. Don't forget about brushes and rollers.

Product Safety Warning (H-phrases)

• EUH211: Warning! Spraying may create dangerous respirable droplets. Do not breathe aerosols or mist.
• H226: Flammable liquid and vapor.
• H312+H332: Harmful to health upon skin contact or inhalation.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H372: Causes damage to organs with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safety Handling Instructions (P-phrases)

• P102: Keep out of reach of children.
• P210: Keep away from heat, hot surfaces, sparks, open flames, and other ignition sources. No smoking.
• P261: Avoid breathing dust/fume/gas/mist/vapors/aerosols.
• P273: Avoid release into the environment.
• P280: Wear protective gloves/protective clothing/protective eyewear/face shield.
• P304+P340: IF INHALED: Transfer person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.