Pragoprimer Standard S2000 priming paint for metal, 0840 reddish-brown, 9 l

Basic synthetic anti-corrosive paint

CHARACTERISTICS AND USE:

Pragoprimer Standard S2000 is a universal priming paint for metal and absorbent substrates for indoor and outdoor environments, especially for underneath synthetic and air-drying coatings, for painting, e.g., sheet metal constructions, machines, metal and wooden furniture, etc. The paint has excellent anti-corrosive properties, very fast drying, and universal applicability.

Key properties:

• active anti-corrosive pigment
• fast drying
• excellent adhesion

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free from grease, rust, and dust, mechanically cleaned. First, the surface must be degreased using a suitable cleaning agent (e.g., BALTECH P6402 technical gasoline, BALTECH P6401 acetone, or, where possible, warm pressurized water containing detergent). To remove any residual salts, the surface must then be rinsed with clean water. Coarse and well-adhered impurities must be removed manually or mechanically (sanding, scraping). Any rust can also be removed manually or mechanically (metal brushes, sanding discs) or using rust removers. When using chemical rust removers, subsequent rinsing with clean water is necessary.
Absorbent substrates must first be primed with a suitable primer that ensures even absorbency of the substrate. Previously painted surfaces must be cleaned, degreased, and stripped of old non-adhering coatings.

DILUTION: thinner BALTECH S6006 (brush, roller), thinner BALTECH S6001 (spraying)

Theoretical yield: 18 - 21 m²/l for one coat

WORKING PROCEDURE:

Before use, thoroughly mix the contents and dilute as needed. The paint is applied with a brush, roller, or by spraying onto a pre-prepared substrate.
Coating / spraying of metal:
For spraying application, first treat problematic areas (corners, edges, welds, surface defects) with a so-called strip coating using a brush, and only after this primer has set should the entire area (including the already painted problematic areas) be sprayed.
1. 1x Pragoprimer Standard S2000 paint, drying time 24 hours. The optimal thickness of one layer is 25 - 30 µm. Drying on metal objects can be accelerated by forced drying at a temperature of 80 °C.
2. Filling as needed, e.g., with polyester filler BKP Rapid TOS.
3. Sanding of filled spots with sandpaper no. 180 - 220 wet.
4. 1x Pragoprimer Standard S2000.
5. Sanding with sandpaper no. 280.
6. 2 to 3x enamel INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matte INDUSTROL UNIMAT S2075

Coating of absorbent substrate:
1. 1x priming with S1023 LAZUROL CLASSIC stain or S1033 LAZUROL IMPREGNATING BASE, drying 24 hours.
2. 1x Pragoprimer Standard S2000 paint, drying 24 hours.
3. 2 to 3x enamel INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matte INDUSTROL UNIMAT S2075.
If filling is needed, proceed as in the previous point (coating of metal).

You may need covering material, such as paper tape or covering film, or even sandpapers. Don't forget brushes and rollers.

Product safety warnings (H-statements)

• EUH208: Contains (see hazardous substances). May produce an allergic reaction.
• EUH211: Warning! Spraying may produce dangerous respiratory droplets. Do not inhale aerosols or mist.
• H226: Flammable liquid and vapour.
• H312+H332: Harmful to health in contact with skin or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H372: Causes damage to organs with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safety handling instructions (P-statements)

• P102: Keep out of reach of children.
• P210: Protect from heat, hot surfaces, sparks, open flame, and other ignition sources. No smoking.
• P261: Avoid breathing dust/fumes/gas/mist/vapours/aerosols.
• P273: Prevent release to the environment.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P304+P340: IF INHALED: Transfer person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call a POISON CENTER/doctor.
• P501: Dispose of contents/container in accordance with product instructions.