Pragoprimer Standard S2000 basic paint for metal, 0100 white, 350 ml

Basic synthetic anticorrosive paint

CHARACTERISTICS AND USE:

Pragoprimer Standard S2000 is a universal basic paint for metal and absorbent substrates for indoor and outdoor environments, especially as a base for synthetic and air-drying coatings, for painting, e.g., sheet metal structures, machines, metal and wooden furniture, etc. The paint has excellent anticorrosive properties, very fast drying time, and universal applicability.

Key properties:

• active anticorrosive pigment
• fast drying
• excellent adhesion

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free from grease, rust, and dust, and mechanically cleaned. First of all, the surface must be degreased using an appropriate cleaning agent (e.g., BALTECH P6402 technical benzene, BALTECH P6401 acetone, or, where possible, warm pressurized water with soap content). To remove any residues of various salts, the surface must then be rinsed with clean water. Coarse and firmly adhering dirt must be removed manually or mechanically (sanding, scraping). Any rust can also be removed manually or mechanically (metal brushes, sanding discs) or with rust removers. If using chemical rust removers, a subsequent rinse with clean water is necessary.
Absorbent substrates must first be primed with a suitable primer that ensures uniform absorbency of the substrate. Previously painted surfaces must be cleaned, degreased, and stripped of old non-adhesive coatings.

DILUTION: thinner BALTECH S6006 (brush, roller), thinner BALTECH S6001 (spraying)

Theoretical coverage: 18 - 21 m²/l for one coat

WORKING PROCEDURE:

Before use, thoroughly stir the contents and dilute as necessary. The paint is applied with a brush, roller, or spraying onto a pre-prepared substrate.
Coating / spraying of metal:
When spraying, problematic areas (corners, edges, seams, surface defects) are first treated with a strip coating using a brush, and only after the surface has set is the entire area sprayed (including already painted problematic areas).
1. 1x paint PRAGOPRIMER STANDARD S2000, drying time of the coat 24 hours. The optimal thickness of one layer is 25 -30 µm. Drying on metal items can be accelerated by drying at temperatures up to 80 °C
2. putty as needed, e.g., with BKP Rapid TOS polyester putty
3. sanding of puttied areas with sandpaper No. 180 - 220 wet
4. 1x PRAGOPRIMER STANDARD S2000
5. sanding with sandpaper No. 280
6. 2 to 3x INDUSTROL UNIVERZÁL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129, or matte INDUSTROL UNIMAT S2075

Coating of absorbent substrate:
1. 1x soaking with S1023 LAZUROL CLASSIC stain, or S1033 LAZUROL IMPREGNATING BASE, drying time 24 hours
2. 1x paint PRAGOPRIMER STANDARD S2000, drying time 24 hours
3. 2 to 3x INDUSTROL UNIVERZÁL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129, or matte INDUSTROL UNIMAT S2075
If puttying is necessary, proceed as in the previous point (coating metal).

You may find a masking material, such as paper adhesive tape or masking film, possibly sanding papers. Don't forget brushes and rollers.

Product safety warnings (H-phrases)

• EUH208: Contains (see hazardous substances). May produce an allergic reaction.
• EUH211: Warning! Spraying may produce dangerous respirable droplets. Do not inhale aerosols or mist.
• H226: Flammable liquid and vapors.
• H312+H332: Harmful to health in contact with skin or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H372: Causes damage to organs with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Instructions for safe handling (P-phrases)

• P102: Keep out of reach of children.
• P210: Protect from heat, hot surfaces, sparks, open flame, and other ignition sources. No smoking.
• P261: Avoid breathing dust/fume/gas/mist/vapor/aerosols.
• P273: Avoid release to the environment.
• P280: Wear protective gloves/clothing/eye protection/face shield.
• P304+P340: IF INHALED: Move person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call the TOXICOLOGICAL INFORMATION CENTER/doctor
• P501: Dispose of contents/container in accordance with the manufacturer's instructions.