Pragoprimer Standard S2000 basic paint for metal, 0100 white, 4 l

Basic synthetic anti-corrosion paint

CHARACTERISTICS AND USE:

Pragoprimer Standard S2000 is a universal basic paint for metal and absorbent substrates for indoor and outdoor environments, especially under synthetic and air-drying coatings, for painting e.g. metal structures, machines, metal and wooden furniture, etc. The paint has excellent anti-corrosion properties, very fast drying, and universal applicability.

Key properties:

• active anti-corrosion pigment
• fast drying
• excellent adhesion

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free of grease, rust, and dust, and mechanically cleaned. First, the surface must be degreased using a suitable cleaning agent (e.g. BALTECH P6402 technical gasoline, BALTECH P6401 acetone, or, where possible, hot pressurized water with a detergent content). To remove residues of various salts, the surface must be rinsed with clean water afterward. Coarse and well-adhering dirt must be removed manually or mechanically (sanding, scraping). Rust can also be removed manually or mechanically (metal brushes, grinding discs) or by using rust removers. If using chemical rust removers, a subsequent rinse with clean water is necessary.
Absorbent substrates must first be primed with a suitable primer that ensures uniform absorbency of the substrate. Previously painted surfaces must be cleaned, degreased, and stripped of old non-adhering coatings.

DILUTION: thinner BALTECH S6006 (brush, roller), thinner BALTECH S6001 (spraying)

Theoretical coverage: 18 - 21 m²/l for one coat

WORKING PROCEDURE:

Before use, thoroughly mix the contents and dilute as needed. The paint is applied with a brush, roller, or spray to the prepared substrate.
Coating/Spraying metal:
During spraying, problematic areas (corners, edges, welds, surface defects) should first be treated with a brush using a strip coating and only after the coating has set should the entire area (including already painted problematic areas) be sprayed.
1. 1x PRAGOPRIMER STANDARD S2000, drying time 24 hours. The optimal thickness of one layer is 25 - 30 µm. Drying on metal items can be accelerated by heating to 80 °C
2. filling as needed, e.g. with polyester filler BKP Rapid TOS
3. sanding the filled areas with grit paper no. 180 - 220 wet
4. 1x PRAGOPRIMER STANDARD S2000
5. sanding with grit paper no. 280
6. 2 to 3x enamel INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matte INDUSTROL UNIMAT S2075

Coating absorbent substrate:
1. 1x priming with S1023 LAZUROL CLASSIC stain, or S1033 LAZUROL IMPREGNATING BASE, drying time 24 hours
2. 1x PRAGOPRIMER STANDARD S2000, drying time 24 hours
3. 2 to 3x enamel INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matte INDUSTROL UNIMAT S2075
If filling is necessary, the procedure is the same as in the previous point (coating metal).

You may find covering material, such as paper masking tape or covering foil, as well as sanding papers. Don’t forget brushes and rollers.

Product safety warnings (H-statements)

• EUH208: Contains (see hazardous substances). May produce an allergic reaction.
• EUH211: Warning! Spraying may produce dangerous respirable droplets. Do not inhale aerosols or mist.
• H226: Flammable liquid and vapor.
• H312+H332: Harmful to health on skin contact or through inhalation.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H372: Causes damage to organs with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safety handling instructions (P-statements)

• P102: Keep out of reach of children.
• P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
• P261: Avoid breathing dust/fume/gas/mist/vapor/aerosols.
• P273: Avoid release to the environment.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P304+P340: IF INHALED: Move person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call a TOXICOLOGICAL INFORMATION CENTER/doctor.
• P501: Dispose of contents/container in accordance with product instructions.