Pragoprimer Standard S2000 basic color for metal, 0110 gray, 600 ml

Basic synthetic anti-corrosive paint

CHARACTERISTICS AND USE:

Pragoprimer Standard S2000 is a universal basic paint for metal and absorbent substrates for both indoor and outdoor environments, especially under synthetic and air-drying coatings, for painting e.g. sheet metal structures, machines, metal and wooden furniture, etc. The paint has excellent anti-corrosive properties, very fast drying, and universal applicability.

Key properties:

• active anti-corrosive pigment
• fast drying
• excellent adhesion

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free from grease, rust, and dust, mechanically cleaned. First of all, the surface must be degreased using a suitable cleaning agent (e.g. BALTECH P6402 technical gasoline, BALTECH P6401 acetone or where possible, warm pressurized water containing detergent). To remove any residual salts, the surface must then be rinsed with clean water. Coarse and well-adhering contaminants must be removed manually or mechanically (sanding, scraping). Any rust can also be removed manually or mechanically (metal brushes, sanding discs) or using rust removers. If chemical rust removers are used, subsequent rinsing with clean water is required.
Absorbent substrates must first be saturated with a suitable saturator that ensures uniform absorbency of the substrate. Previously painted surfaces must be cleaned, degreased, and stripped of old non-adhering coatings.

DILUTION: thinner BALTECH S6006 (brush, roller), thinner BALTECH S6001 (spraying)

Theoretical coverage: 18 - 21 m²/l for one layer

WORKING PROCEDURE:

Before use, stir the contents thoroughly and dilute if necessary. The paint is applied with a brush, roller, or by spraying on the prepared substrate. 
Coating / spraying of metal:
When spraying, problem areas (corners, edges, welds, surface defects) must first be treated with a so-called strip coating using a brush, and only after this coating has set, the entire area is sprayed (including already painted problem areas).
1. 1x PRAGOPRIMER STANDARD S2000, drying time 24 hours. The optimal thickness of one layer is 25 -30 µm. Drying on metal objects can be accelerated by drying at 80 °C
2. filling as needed e.g. with BKP Rapid TOS polyester filler
3. sanding of filled areas with sandpaper no. 180 - 220 wet
4. 1x PRAGOPRIMER STANDARD S2000
5. sanding with sandpaper no. 280
6. 2 to 3x enamel INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matt INDUSTROL UNIMAT S2075

Coating of absorbent substrates:
1. 1x priming with S1023 LAZUROL CLASSIC, or S1033 LAZUROL IMPREGNATING BASE, drying 24 hours
2. 1x PRAGOPRIMER STANDARD S2000, drying 24 hours
3. 2 to 3x enamel INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129 or matt INDUSTROL UNIMAT S2075
If filling is needed, proceed as in the previous point (coating of metal).

You may find protective materials, such as paper masking tape or masking film, or sandpapers. Don’t forget brushes and rollers.

Product safety warnings (H-statements)

• EUH208: Contains (see hazardous substances). May produce an allergic reaction.
• EUH211: Warning! Hazardous respirable droplets may be formed when sprayed.Do not inhale aerosols ormist.
• H226: Flammable liquid and vapors.
• H312+H332: Harmful to health on contact with skin or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H372: Causes damage to organs through prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safety handling instructions (P-statements)

• P102: Keep out of reach of children.
• P210: Protect from heat, hot surfaces, sparks, open flame, and other sources of ignition. No smoking.
• P261: Avoid breathing dust/fume/gas/mist/vapor/aerosol.
• P273: Prevent release to the environment.
• P280: Wear protective gloves/protective clothing/protective eyewear/face shield.
• P304+P340: IF INHALED: Remove person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call a POISON CENTER/doctor
• P501: Dispose of contents/container in accordance with the instructions on the product.