Pragoprimer Standard S2000 basic paint for metal, 0840 red-brown, 2.5 l

Basic synthetic anti-corrosive paint

CHARACTERISTICS AND USE:

Pragoprimer Standard S2000 is a versatile basic paint for metal and absorbent substrates for indoor and outdoor environments, especially under synthetic and air-drying coatings, for coatings of e.g. sheet metal structures, machines, metal and wooden furniture, etc. The paint has excellent anti-corrosive properties, very fast drying, and universal applicability.

Key properties:

• active anti-corrosive pigment
• fast drying
• excellent adhesion

SUBSTRATE PREPARATION:

The substrate for application must be clean, dry, free of grease, rust, and dust, mechanically cleaned. First of all, the surface must be degreased using an appropriate cleaning agent (e.g. BALTECH P6402 technical benzene, BALTECH P6401 acetone, or where possible, hot pressurized water containing detergent). To remove any residue of various salts, the surface must then be rinsed with clean water. Coarse and well-adhering dirt must be removed manually or mechanically (sanding, scraping). Any rust can also be removed manually or mechanically (metal brushes, sanding discs) or using rust removers. If chemical rust removers are used, a subsequent rinse with clean water is necessary.
Absorbent substrates should be primed with a suitable primer that ensures uniform absorbency of the substrate. Previously painted surfaces must be cleaned, degreased, and stripped of old non-adherent coatings.

DILUTION: thinner BALTECH S6006 (brush, roller), thinner BALTECH S6001 (spraying)

Theoretical coverage: 18 - 21 m²/l for one coat

WORKING PROCEDURE:

Before use, thoroughly mix the contents and dilute if necessary. The paint is applied with a brush, roller, or by spraying onto a pre-prepared substrate.
Coating / spraying metal:
When spraying, first treat problematic areas (corners, edges, seams, surface defects) with a so-called stripe coat using a brush, and only after this coat has slightly dried, spray the entire area (including already painted problematic places).
1. 1 coat of PRAGOPRIMER STANDARD S2000, drying time 24 hours. The optimal thickness of one layer is 25 -30 µm. Drying on metal objects can be accelerated by heat drying up to 80 °C.
2. filling as needed, e.g. with BKP Rapid TOS polyester filler.
3. sanding of filled areas with sandpaper no. 180 - 220 wet.
4. 1 coat of PRAGOPRIMER STANDARD S2000.
5. sanding with sandpaper no. 280.
6. 2 to 3 coats of INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129, or matte INDUSTROL UNIMAT S2075

Coating of absorbent substrate:
1. 1 coat of impregnation S1023 LAZUROL CLASSIC, or S1033 LAZUROL IMPREGNATING BASE, drying time 24 hours.
2. 1 coat of PRAGOPRIMER STANDARD S2000, drying time 24 hours.
3. 2 to 3 coats of INDUSTROL UNIVERSAL S2013, INDUSTROL PLUS S2071, INDUSTROL PROFI U2129, or matte INDUSTROL UNIMAT S2075.
If filling is needed, proceed as in the previous step (coating metal).

You may find covering material, such as paper adhesive tape or covering foil, as well as sanding papers. Don't forget brushes and rollers.

Product safety warnings (H-statements)

• EUH208: Contains (see hazardous substances). May produce an allergic reaction.
• EUH211: Warning! Spraying may produce hazardous respirable droplets. Do not breathe aerosol or mist.
• H226: Flammable liquid and vapors.
• H312+H332: Harmful to health in contact with skin or if inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H372: Causes damage to organs with prolonged or repeated exposure.
• H411: Toxic to aquatic organisms, with long-lasting effects.

Safety handling instructions (P-statements)

• P102: Keep out of reach of children.
• P210: Protect from heat, hot surfaces, sparks, open flame, and other ignition sources. No smoking.
• P261: Avoid breathing dust/smoke/gas/mist/vapors/aerosols.
• P273: Avoid release to the environment.
• P280: Wear protective gloves/protective clothing/eye protection/face shield.
• P304+P340: IF INHALED: Remove person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call the POISON CENTER/doctor.
• P501: Dispose of contents/container in accordance with product instructions.