Industrol S2013 universal gloss top coat for metal and wood, 5149 light green, 4 l

Glossy synthetic top enamel for wood and metal

CHARACTERISTICS AND USE:

The product is intended for glossy top coats for metals, wood, and materials such as masonry for outdoor and indoor use. The substrate must always be treated with an appropriate primer. The product has excellent opacity, high gloss, and very good weather resistance. It has good flow and workability. It is available in a wide range of shades. The product has a long shelf life during which the useful properties of the coating do not change. The product is suitable for painting fences, doors, frames, sills, small structures and industrial items, wooden furniture and paneling, garden furniture, washable and abrasion-resistant wall coatings.

Key properties:

• Long-term resistance to weather conditions
• Stable gloss
• Urethane binders

SUBSTRATE PREPARATION:

Wood must be clean, dry, well-sanded, with a moisture content of no more than 12% and free from resin residues before application. Concrete or masonry substrates must be dry, cohesive, free from dirt, properly cured (typically 4 – 6 weeks), and structurally insulated against ground moisture. Metal substrates must be dry, clean, free from grease, rust, and dust, and mechanically cleaned. Absorbent substrates must be further primed with an appropriate primer and possibly treated with a corresponding base material. Metal substrates must be coated with a suitable anti-corrosive primer. Previously painted surfaces must be cleaned, degreased, and stripped of original non-adhering coatings.

DILUTION: thin with BALTECH S6006 (brush, roller), BALTECH S6001 (spraying)

Theoretical coverage: 14 - 16 m2/l in one coat

WORKING PROCEDURE:

Before use, the contents must be thoroughly mixed and diluted as necessary.

Coating of metal items:
1.) 1x coat of PRAGOPRIMER STANDARD S2000 or FORMEX PRIMER FOR GALVANIZED S2003, PRAGOPRIMER UNIVERSAL S2035
2.) local filling with putty, sanding the filled area with sandpaper
3.) 1x coat of PRAGOPRIMER STANDARD S2000 or PRAGOPRIMER UNIVERSAL S2035
4.) sanding with sandpaper No. 280-320 wet
5.) 2 to 3x INDUSTROL UNIVERSAL S2013

Coating of wooden items:
1.) 1x coat with Lazurolem Classic S1023, drying for 24 hours.
2.) 1-2x coats of PRAGOPRIMER PLUS S2070 or LAZUROL WINDOW PRIMER S2060.
3.) 2-3x coats of INDUSTROL UNIVERSAL S2013. Each coat of enamel must dry for at least 24 hours (20 °C).

Covering material may come in handy, such as paper masking tape or covering foil, or sandpapers. Don’t forget brushes and rollers.

Product safety warnings (H-statements)

• EUH066: Repeated exposure may cause skin dryness or cracking.
• EUH208: Contains (see hazardous substances). May produce an allergic reaction.
• EUH211: Warning! Dangerous respirable droplets may be formed when sprayed. Do not breathe aerosols or mist.
• H226: Flammable liquid and vapour.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H336: May cause drowsiness or dizziness.
• H373: May cause damage to organs with prolonged or repeated exposure.
• H412: Harmful to aquatic life with long-lasting effects.

Safety handling instructions (P-statements)

• P101: If medical advice is needed, have product container or label at hand.
• P102: Keep out of reach of children.
• P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
• P260: Do not breathe dust/fume/gas/mist/vapours/aerosols.
• P261: Avoid breathing dust/fume/gas/mist/vapours/aerosols.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P302+P352: IF ON SKIN: Wash with plenty of water and soap
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: Call a POISON CENTER/doctor if you feel unwell
• P314: Get medical advice/attention if you feel unwell.
• P501: Dispose of contents/container to local regulations.