Betex s2852 2v1 base and top coat for pools 0440 dark blue, 9 kg

Polystyrene paint for pools BETEX 2v1 FOR POOLS S2852.

CHARACTERISTICS AND USE:

The paint is used as both a primer and a top coat and is intended for painting concrete substrates, masonry and plasters exposed to the effects of water, water vapor, or high relative humidity. The paint can also be used for painting pools and metal tanks. The paint is not intended for painted concrete surfaces.

Key features:

• 100% impermeable
• always flexible
• high resistance to water and water vapor
• resistant to pool chemicals

SUBSTRATE PREPARATION:

The substrate to be painted must be dry, cohesive, clean, well-cured (usually 4 – 6 weeks), and constructionally insulated against ground (bottom) moisture. The surface must be free of dust and must not be contaminated with grease, asphalt residues, and petroleum products. Dust should ideally be vacuumed using a powerful vacuum cleaner. If cleaning with water jetting, the substrate must be allowed to dry thoroughly. In the case of substrates with larger unevenness, sanding is recommended. The relative humidity of the substrate must not exceed 5%. Old coatings must be removed thoroughly.

DILUTION: diluent BALTECH S6005

Theoretical coverage: 5 - 6 m²/ 1 kg for one coat

APPLICATION PROCEDURE:

The coating must be well mixed before application so that no sediment remains at the bottom, and if used as a primer, it should be diluted. Apply with a brush or roller on the previously prepared substrate.

Painting plaster, masonry, concrete:

• 1 to 2 times priming with BETEX 2v1 FOR POOLS S2852 diluted with BALTECH S6005 at a ratio of 1:1
• 3 to 5 times coating with BETEX 2v1 FOR POOLS S2852

Metal coating:

• 1 time undercoat with FORMEX PRIMER FOR GALVANIZED S2003. The top coat is applied over the primer within 24 hours after application or after 7 days
• 3 to 4 times coating with BETEX 2v1 FOR POOLS S2852 (interval between layers 4 hours / 23 °C).

The thickness of the entire coating system must be at least 120 µm. The coating can be exposed to water effects no earlier than after 7 days. The stability of color shades may be affected by exposure to harsh chemical environments. This phenomenon does not affect the effectiveness of the coating.

Product safety warnings (H-statements)

• EUH208: Contains (see hazardous substances). May cause an allergic reaction.
• EUH211: Warning! Dangerous respiratory droplets may be formed during spraying. Do not inhale aerosols or mist.
• H226: Flammable liquid and vapor.
• H312+H332: Harmful to health in contact with skin or when inhaled.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H335: May cause respiratory irritation.
• H373: May cause organ damage with prolonged or repeated exposure.

Instructions for safe handling (P-statements)

• P101: If medical advice is needed, have product container or label at hand.
• P102: Keep out of reach of children.
• P210: Keep away from heat, hot surfaces, sparks, open flames and other sources of ignition. No smoking.
• P260: Do not breathe dust/fume/gas/mist/vapors/aerosols.
• P261: Avoid breathing dust/fume/gas/mist/vapors/aerosols.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P302+P352: IN CASE OF SKIN CONTACT: Wash with plenty of water and soap
• P304+P340: IF INHALED: Move person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call the POISON CENTER/doctor/ tel. 224 919 293 or 224 915 402 (24 hours a day)
• P501: Dispose of contents/container in accordance with the instructions on the product.