Detecha Izoban paint for concrete, RAL 1001 beige, 2 kg

Synthetic coating material for concrete. 100% water resistant, resistant to oils, salt solutions, weak acids and alkalis, short-term exposure to diesel fuel. Mechanically durable. Tolerates permanent thermal load up to +50 °C. Easily repairable with a simple recoat. A product with an excellent quality-to-price ratio.

Uses:
Outdoor and indoor coatings for concrete. Concrete floors (garages, utility spaces, basements, workshops, balconies, etc.). Concrete swimming pools, water tanks (test certificate from SZÚ Prague), masonry, plasters. Steel tanks primed with a basic anti-corrosion coating (e.g. Fest Primer, Superkov, etc.)

Warning:
Walkable after 8 hours. Pool filling after 7 days. Final curing takes 14 days to 3 weeks.

Dilution:
If necessary, the coating can be diluted with thinner S 6005.

Coverage:
The coverage of the coating material depends on the quality of the surface being coated and ranges from 6 - 8 m² per 1 kg in one layer at an average dry film thickness of 50 μm.

Surface preparation:
The concrete must be absorbent, possibly roughened, not seal-coated, well-cured, dry (maximum relative humidity of the substrate 15%), insulated against rising moisture. It must be cohesive (concrete tensile cohesion min. 1.5 MPa), free from all dirt and poorly adhering particles. In case of doubt about the suitability for the specific substrate (e.g. screed, old coating), we recommend performing a test coat on a smaller area.

Application method:
Before use, the material must be thoroughly mixed and diluted if necessary. Before coating untreated concrete surfaces, we recommend priming with a diluted coating in a ratio of 1 part Izoban to 1 part thinner S 6005. For larger areas, it is advisable to use material from one production batch; if different batches are used, mix them to ensure a uniform color shade. It is applied with a brush or roller in at least two layers depending on the absorbency of the substrate, always after the previous layer has dried. The total thickness of the entire coating system must be approximately 100 µm after drying. A thicker layer of paint significantly prolongs the drying and curing time, so it is essential to proceed with thin layers. For coatings on steel tanks and barrels, we recommend pre-coating the surface with a basic anti-corrosion primer (Fest primer and Superkov) and applying the subsequent Izoban coat only after thorough curing of the primer for at least 48 hours. Work in a well-ventilated environment at a temperature of +10 to +25 °C. Do not work in direct sunlight!

Warning:
The paint is not intended for coatings that come into direct contact with food, feed, and drinking water, nor for children’s furniture and toys. It cannot be applied to insufficiently dried surfaces, e.g. in damp, poorly ventilated areas. The coating does not withstand the action of gasoline and organic solvents.

Product safety warnings (H-phrases)

• EUH066: Repeated exposure may cause drying or cracking of the skin.
• H226: Flammable liquid and vapor.
• H312: Harmful in contact with skin.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H332: Harmful if inhaled.
• H335: May cause respiratory irritation.
• H362: May harm breast-fed children.
• H373: May cause damage to organs through prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safety handling instructions (P-phrases)

• P102: Keep out of reach of children.
• P201: Obtain special instructions before use.
• P210: Keep away from heat, hot surfaces, sparks, open flames, and other ignition sources. No smoking.
• P263: Avoid contact during pregnancy/breastfeeding.
• P271: Use only outdoors or in a well-ventilated area.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P302+P352: IF ON SKIN: Wash with plenty of water and soap.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing.
• P312: Call a TOXICOLOGICAL INFORMATION CENTER/doctor if you feel unwell.
• P391: Collect spillage.
• P501: Dispose of contents/container in accordance with product instructions.