EPOLEX bathtub paint S2321O + hardener S7300, 940 g

EPOLEX BATHTUB PAINT S2321O is a special two-component epoxy paint designed for the renovation of the surfaces of enamel bathtubs.

CHARACTERISTICS AND USE:

The paint is intended for the renovation of the surfaces of enamel bathtubs and shower trays. It is not suitable for acrylic surfaces. The paint has been approved for painting the surfaces of food processing equipment that comes into contact with food.
Before use, the paint should be mixed and combined with the hardener in the prescribed ratio.

Key properties:

• highly durable coating
• high gloss finish
• long-lasting durability

SUBSTRATE PREPARATION:

Thoroughly wash the bathtub with an effective degreasing agent to remove grease and limescale deposits. For good adhesion, the surface should be thoroughly abraded with sandpaper grit 280 - 320 while wet. Rinse with water and let dry. Damaged areas (chipped enamel, etc.) should be filled with epoxy putty for metal. After curing, sand with water-proof sandpaper grit 320 - 360. Clean the surface with a soap solution. Dismantle the fittings (drain and overflow), thoroughly sand and clean the exposed areas. Prevent water from dripping. The surface should be matte, dry, and completely clean. Mask the bathtub with masking tape.

DILUTION: thinner BALTECH S6300

CURING: EPOLEX HARDENER S7300. Weight ratio for curing: EPOLEX BATHTUB PAINT S2321 O - 100 weight parts : EPOLEX HARDENER S7300 - 33 weight parts.
Volume ratio for curing: EPOLEX BATHTUB PAINT S2321 O - 70 volume parts : EPOLEX HARDENER S7300 - 30 volume parts. The cured mixture must be used within 8 hours.

Theoretical coverage: 11 - 15 m²/1 kg of cured mixture for one layer of 30 - 40 µm

WORKING PROCEDURE:

Thoroughly mix the paint before use, cure with the prescribed amount of EPOLEX HARDENER S7300, and mix thoroughly again. Allow to stand for about 15 minutes to defoam. Apply with a brush, roller, or spray on a pre-prepared substrate. The substrate temperature must be at least 15 °C. Airflow (draft) may cause dusting and other appearance defects. Apply in cross strokes in an even thinner layer. The second coat should be applied 24 hours later. Not suitable for outdoor use.

You might find covering material, such as paper adhesive tape or covering foil, or sanding papers. Don’t forget brushes and rollers.

Safety warnings for the product (H-statements)

• EUH205: Contains epoxy components. May produce an allergic reaction.
• H226: Flammable liquid and vapors.
• H312+H332: Harmful to health upon skin contact or inhalation.
• H314: Causes severe skin burns and eye damage.
• H315: Causes skin irritation.
• H317: May cause an allergic skin reaction.
• H318: Causes serious eye damage.
• H335: May cause respiratory irritation.
• H373: May cause damage to organs with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.
• H412: Harmful to aquatic life with long-lasting effects.

Safe handling instructions (P-statements)

• P101: If medical advice is needed, have product container or label at hand.
• P102: Keep out of reach of children.
• P210: Keep away from heat, hot surfaces, sparks, open flames, and other ignition sources. No smoking.
• P261: Avoid breathing dust/fume/gas/mist/vapors/aerosols.
• P273: Avoid release to the environment.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P304+P340: IF INHALED: Move person to fresh air and keep comfortable for breathing.
• P305+P351+P338: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P310: Immediately call a POISON CENTER/doctor/ tel. 224 919 293 or 224 915 402 (24 hours a day)
• P312: If you feel unwell, call a POISON CENTER/doctor/ tel. 224 919 293 or 224 915 402 (24 hours a day)
• P333+P313: If skin irritation or rash occurs: Get medical advice/attention.
• P501: Dispose of contents/container in accordance with product instructions.