Detecha Izoban waterproof paint for concrete, blue, 20 kg

Synthetic coating for concrete. 100% waterproof, resistant to oils, salt solutions, weak acids and bases, temporarily to diesel fuel. Mechanically resistant. Tolerates permanent thermal stress up to +50 °C. Easily repairable by simple re-coating. A product with an excellent price-quality ratio.

Usage:
Outdoor and indoor coatings for concrete. Concrete floors (garages, commercial spaces, basements, workshops, balconies, etc.). Concrete pools, water tanks (certificate from SZÚ Prague), masonry, plasters. Steel tanks coated with a basic anti-corrosive primer (e.g. Fest Primer, Superkov, etc.)

Warning:
Walkable after 8 hours. Pool filling after 7 days. Final curing 14 days to 3 weeks.

Dilution:
If necessary, the coating can be diluted with thinner S 6005.

Yield:
The yield of the paint depends on the quality of the substrate and ranges from 6 - 8 m² per 1 kg in one layer at an average dry film thickness of 50 μm.

Substrate preparation:
Concrete must be absorbent, possibly roughened, not cracked, well-cured, dry (maximum relative humidity of the substrate 15%), insulated against moisture from below. It must be cohesive (cohesion of concrete in tension min. 1.5 MPa), free from dirt and loose particles. In case of doubts about the suitability of use on the given substrate (e.g. leveling compound, old coat), we recommend performing a test coat on a smaller area.

Application method:
Before use, the material must be thoroughly mixed and diluted if necessary. Before coating previously untreated concrete surfaces, we recommend priming with a diluted coating in a ratio of 1 part Izoban to 1 part thinner S 6005. For larger areas, we recommend using material from the same production batch, or mixing different batches to ensure a uniform color shade. It is applied with a brush or roller in at least two layers depending on the absorbency of the substrate, always after the previous layer has dried. The thickness of the entire coating system must be about 100 µm after drying. A thicker layer of paint significantly prolongs the drying time and curing, so it is necessary to proceed with thin layers. In the case of coatings for steel tanks and barrels, we recommend pre-treating the surface with a basic anti-corrosive primer (Fest primer and Superkov) and applying the Izoban coating only after thorough curing of the base for at least 48 hours. Work in a well-ventilated environment at temperatures between +10 to +25°C. Do not work in direct sunlight!

Warning:
The paint is not intended for coatings that come into direct contact with food, feed, and drinking water, and for coatings of children's furniture and toys. It cannot be applied on inadequately dried substrates, e.g. in humid, poorly ventilated areas. The coating does not withstand the effects of gasoline and organic solvents.

Product safety warnings (H-statements)

• EUH066: Repeated exposure may cause skin dryness or cracking.
• H226: Flammable liquid and vapors.
• H312: Harmful to health in contact with skin.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H332: Harmful to health if inhaled.
• H335: May cause respiratory irritation.
• H362: May harm breastfeeding infants through mother's milk.
• H373: May cause organ damage with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safe handling instructions (P-statements)

• P102: Keep out of reach of children.
• P201: Obtain special instructions before use.
• P210: Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking.
• P263: Avoid contact during pregnancy/breastfeeding.
• P271: Use only outdoors or in a well-ventilated area.
• P280: Wear protective gloves/protective clothing/eye protection/face protection.
• P302+P352: IN CASE OF CONTACT WITH SKIN: Wash with plenty of water and soap
• P305+P351+P338: IN CASE OF EYE CONTACT: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call a POISON CENTER/doctor
• P391: Collect spillage.
• P501: Dispose of contents/container in accordance with product instructions.