Detecha Izoban concrete paint, blue, 2 kg

Synthetic coating for concrete. 100% water-resistant, resistant to oils, salt solutions, weak acids and bases, temporarily diesel fuel. Mechanically resistant. Can withstand permanent thermal loads up to +50 °C. Easily repairable by simple re-coating. A product with an excellent quality-to-price ratio.

Application:
Outdoor and indoor coatings for concrete. Concrete floors (garages, non-residential areas, basements, workshops, balconies, etc.). Concrete pools, water reservoirs (test SZÚ Prague), masonry, plasters. Steel tanks coated with a primer anti-corrosive coating (e.g., Fest Primer, Superkov, etc.)

Warning:
Walkable in 8 hours. Pool filling in 7 days. Final curing 14 days to 3 weeks.

Dilution:
If necessary, the coating can be diluted with thinner S 6005.

Coverage:
The coverage of the coating material depends on the quality of the painted surface and ranges from 6 to 8 m² per 1 kg in one layer at an average dry film thickness of 50 μm.

Substrate preparation:
The concrete must be absorbent, roughened if necessary, not previously coated, well-cured, dry (maximum relative humidity of the substrate 15%), and isolated against rising damp. It must be cohesive (cohesion of concrete in tension min. 1.5 MPa), free of all dirt and poorly adhering particles. In case of doubt about the suitability of the substrate (e.g., screed, old coating), we recommend performing a test coating on a smaller area.

Application method:
Before use, the material must be thoroughly stirred and diluted if necessary. Before painting untreated concrete surfaces, we recommend performing priming with diluted paint at a ratio of 1 part Izoban to 1 part thinner S 6005. For larger areas, it is recommended to use material from the same production batch; if different batches are used, mix them to ensure a uniform color shade. Apply with a brush or roller in at least two layers according to the absorbency of the substrate, waiting for the previous layer to dry. The thickness of the entire coating system must be approximately 100 µm after drying. A thicker layer of paint significantly prolongs the drying and curing time, so it is essential to work in thin layers. For coatings of steel tanks and barrels, we recommend pre-coating the surface with a primer anti-corrosive paint (Fest Primer and Superkov) and then applying Izoban only after the primer has thoroughly cured for at least 48 hours. Work in a well-ventilated environment at a temperature between +10 and +25°C. Do not work in direct sunlight!

Warning:
The paint is not suitable for coatings that come into direct contact with food, animal feed, and drinking water, and for coatings of children's furniture and toys. It cannot be applied to poorly dried substrates, e.g., in humid, insufficiently ventilated areas. The coating is not resistant to benzene and organic solvents.

Product safety warnings (H-statements)

• EUH066: Repeated exposure may cause drying or cracking of the skin.
• H226: Flammable liquid and vapors.
• H312: Harmful to health in contact with skin.
• H315: Causes skin irritation.
• H319: Causes serious eye irritation.
• H332: Harmful to health if inhaled.
• H335: May cause respiratory irritation.
• H362: May harm nursing infants through breast milk.
• H373: May cause organ damage with prolonged or repeated exposure.
• H411: Toxic to aquatic life with long-lasting effects.

Safe handling instructions (P-statements)

• P102: Keep out of reach of children.
• P201: Obtain special instructions before use.
• P210: Protect from heat, hot surfaces, sparks, open flame, and other ignition sources. No smoking.
• P263: Avoid contact during pregnancy/breastfeeding.
• P271: Use only outdoors or in a well-ventilated area.
• P280: Wear protective gloves/protective clothing/eye protection/face shield.
• P302+P352: IN CASE OF SKIN CONTACT: Wash with plenty of water and soap
• P305+P351+P338: IN CASE OF EYE CONTACT: Rinse cautiously with water for several minutes. Remove contact lenses if present and easy to do. Continue rinsing.
• P312: If you feel unwell, call the TOXICOLOGY INFORMATION CENTER/doctor
• P391: Collect spilled product.
• P501: Dispose of contents/container in accordance with product instructions.